Admin
Admin
عدد المساهمات : 272
تاريخ التسجيل : 19/03/2013
 |  موضوع: اصدارت الــــ NanoStation M5 + Loco  الأربعاء يونيو 25, 2014 12:53 am | |
| شبكة سكاي نت لخدمات الانترنت اللاسلكي
تقدم لكم اصدارت البيكو القديمة والحديثة لترقية او العودة اليها بعد حدفها من موقع الشركة
نسخرها هنا بين ايديكم وبالمجان
NanoStation M5 + Loco نبدة محتصرة عن كل اصدار وبعده التحميل AirOS V Firmware Revision History
====================================================================
Supported products
* NanoBeam M2/M5
* AirGrid M5 HP
* NanoStation M5
* NanoStation M5 Loco
* Rocket M5/Titanium
====================================================================
Version 5.5.9(XW)- Service Release (April 04, 2014)
----------------------------------------------------
Fixes:
- Fix: Device operating in AP mode does not keep selected frequency and reverts to Auto (US version products only)
- Fix: Issues uploading back up configuration file (US version products only)
- Fix: Correct antenna selection when connecting to 802.11 a/b/g devices (all XW)
Version 5.5.8(XW)- Service Release (January 24, 2014)
----------------------------------------------------
Regulatory updates:
- New: Regulatory changes for Greece
- New: Regulatory changes for Thailand
- New: Add Croatia under EU regulatory rules
- New: Split Serbia and Montenegro
- New: Remove Compliance Test mode
- New: Lock selected country for all EU countries/Switzerland. Reset to factory defaults is required to order to change country
- New: Available frequency list is updated for UK when operating in 30MHz channel width
- New: Various regulatory updates
New:
- New: Remote Provisioning Functionality for AirGateway
Fixes:
- Fix: Disabling DHCP server leaves dnsmasq running
- Fix: NanoBeam Mx does not report wlanTxLatency to airControl (AC/AC2)
- WEB UI: Validate location coordinates
- WEB UI: Copyright updates
---------
====================================================================
Version 5.5.8-Service Release (January 23, 2014)
----------------------------------------------
Regulatory updates:
- New: Regulatory changes for Greece
- New: Regulatory changes for Thailand
- New: Add Croatia under EU regulatory rules
- New: Split Serbia and Montenegro
- New: Remove Compliance Test mode
- New: Lock selected country for all EU countries/Switzerland. Reset to factory defaults is required to order to change country
- New: Available frequency list is updated for UK when operating in 30MHz channel width
New:
- New: Remote Provisioning Functionality for AirGateway
Improvements:
- airMax: Rate drops when using narrow channel widths on AP with more than 30 clients
- Ethernet: Ethernet negotiation issues after ESD damage
- NanoBridge M5: Cold temperature issues
Fixes:
- Fix: DFS frequencies are not functional for Canada (Rocket M5 Titanium)
- Fix: Possible fix for unexpected AP reboots
- Fix: Auto IP Address generation for MAC addresses ending with FF:FF and 00:00
- Fix: SSL server accepts weak ciphers
- Fix: SSH server (dropbear) update to version v2013.58
- Fix: Disabling DHCP server leaves dnsmasq running
- WEB UI: Automatic FW download from web site
- WEB UI: Validate location coordinates
- WEB UI: Copyright updates
Version 5.5.6-Service Release (June 03, 2013)
----------------------------------------------
Regulatory updates:
- New: Lock country code for Ukraine
- Fix: Rocket M5 Titanium: DFS band unlock with authorisation key
- Fix: Remove DFS enable/disable option for EU/Switzerland, turn DFS ON after FW upgrade
- Fix: Update maximum EIRP from 20dBm to 23dBm for EU countries (indoor range)
- Fix: Update maximum EIRP from 20dBm to 23dBm for Vietnam (in frequency range 5150-5350 MHz)
- Fix: Regulatory update for Norway (5GHz band frequencies and EIRP limits update)
- WEB UI: Channel list with indication for Indoor channels (EU/Switzerland)
- WEB UI: Possibility to hide indoor channels (EU/Switzerland)
Fixes:
- Fix: Sometimes AP stops passing traffic in PtMP setup
- Fix: UAPSD power saving problems
- Fix: In some cases web server may lock up after some time due to memory leak (possible fix)
- Fix: Polycom SpectraLink 8030 wireless phone connection issues
- Fix: AirGrid M5 HP: Change Antenna gain from 28dBi to 27dBi according antenna specification
Version 5.5.4-Service Release (March 13, 2013)
----------------------------------------------
New:
- New: Data rate module: Alternative data rate algorithm option
- New: WEB UI: Audio option for Antenna Alignment Tool
- New: WEB UI: "Feed only - 3dBi" option for antenna type (AirGrid and NanoBridge models only)
Improvements:
- airMax: Improved performance in PtMP scenarios
- airMax: Lower latency in Long Range PTP mode
- airMax: Voice performance/latency improvements in PtMP scenarios
- QoS: Map commonly used VoIP TOS values (0x68, 0xb8) to Voice queue
- Speed test: Improved timeout/errors handling and reporting
- TFTP recovery: Reset configuration to factory defaults when executing TFTP recovery mode without need to hold Reset button for 15sec and upload firmware image
- airView: Update certificate
- WEB UI: Show if custom scripts are present on device
- WEB UI: Show signal strength from remote radio in Station information window (airMax mode only)
- WEB UI: Show Station TX/RX bit rate statistics
- WEB UI: Disable WEB UI while airView is running
- WEB UI: Automatically redirect to HTTPS port when running Speed test
- WEB UI: Make MAC addresses in Main page easily selectable
- WEB UI: Add help text for UBNT/Advanced settings pages
- WEB UI: Improved FW update failure messages
- WEB UI: Do not offer to apply configuration changes if there are no any changes made
- WEB UI: Latitude/Longitude setting validation
- WEB UI: Interface Language update: French translations
- WEB UI: Interface Language update: Lithuanian translation
- Stability: Check filesystem on boot
- Stability: Memory leak protection for less than 1MB of RAM
- Stability: HW watchdog in u-boot
Fixes:
- Fix: airMax: Radio is transmitting when operating in airView mode (AP mode only)
- Fix: airMax: Long range PtP mode: AP gets stuck at 81Mbps rate and transmit throughput goes down
- Fix: airMax: Sometimes AP locks up when applying configuration changes (possible fix)
- Fix: airSync: Rocket Titanium airSync Slave doesn't connect to airSync Master
- Fix: airSelect: Default airSelect announce count set to 30
- Fix: airView: airView does not start when Device Name contains comma symbol
- Fix: airView: M900/M3/M365/M6 products does not scan full frequency range
- Fix: Detect Ethernet loopback on defective device and bring Ethernet interface down
- Fix: Sometimes M Series devices hang during reboot (except Titanium)
- Fix: Change Max MTU to 2024 bytes on both Ethernet interfaces
- Fix: Returning from Test mode does not revert some configuration changes
- Fix: Redirection issue when enabling/disabling HTTPS
- Fix: Satellite signal bar is centred under IE
- Fix: During upgrade disable default route if DHCP client is configured
- Fix: DHCP fallback IP isn't set
- Fix: Memory leak in Main page with IE8/IE9 (session timeout implemented)
- Fix: Low power mode fix for newer revisions of NanoStation M5
- Fix: Device discovery issue when DMZ port is enabled
- Fix: Cannot switch from Advanced to Simple Configuration mode when network role is Router
- Fix: Auto Channel does not follow channel plan for Canada (Rocket Titanium)
- Fix: OSPF and other unregistered multicast traffic transmit problems in PtMP
- Fix: Skip EAP security certificate date validation if device date is before certificate start date
- Fix: Do not send discovery/ARP requests through bridge ports
- Fix: Enable busybox option to prefer IPv4
- Fix: UPnP: Router should accept "PORT FORWARD" requests from LAN side only
- Fix: Sometimes station can't associate when switching from open to WPA security
- Fix: Enable DFS when choosing country Austria
- Fix: Disable "Block Management" option for WAN in default configuration (AirRouter, AirRouter HP, PowerAP N)
Regulatory updates:
- Enable DFS for Germany upper band (5.8GHz) channels
- Update New Zealand allowed frequencies for 5GHz
- Update Chilean allowed frequencies for 5GHz
Version 5.5.3-Production Release (October 25, 2012)
--------------------------------------------------
New product support:
- New: Rocket M6
- New: AirGrid M2 HP (re-designed)
- New: AirGrid M5 HP (re-designed)
Version 5.5.2-Service Release (August 17, 2012)
----------------------------------------------
New product support:
- New: Rocket M2 Titanium
- New: Rocket M5 Titanium
- New: NanoStation M6
Regulatory Updates:
- New: Enable DFS frequencies for US/Puerto Rico/ Canada for NanoStationM5/Loco M5/Rocket M5/Rocket M5 GPS/NanoBridge M5 models
- New: Lock Indonesia country code: once selected at Login page do not allow to change country unless reset to defaults
- New: Remove DFS enable/disable option for Austria, turn DFS ON after upgrade for Austria. Keep DFS enable/disable option for rest of EU countries
- Fix: Regulatory rules update for India 2.4GHz band
- Fix: Move Puerto Rico under US regulatory domain
Fixes:
- Fix: AirMax: When one of the clients reboot all others are disconnected from AP
- Fix: AirMax: Unexpected device reboots on high load/PTMP (possible fix)
- Fix: Traffic shaping ingress rules on LAN port in some cases block Internet traffic
- Fix: Traffic shaping bursting is increased to the maximum allowed value according to configured throughput limits
- Fix: Association to non-broadcasting SSID CISCO AP takes couple minutes
- Fix: Complex AP-repeater setup creates loop in this network
- Fix: Increase Password attribute length to 18 when sending empty password to RADIUS server
- Fix: Auto Channel selection logic improvement
- Fix: DFS: Allow UNII-2 band for Canada w/o unlock key for approved product models
- Fix: Traffic Shaper rules changes during upgrade from v5.3.5
- Fix: PPPoE stops sending PPPoE Discovery packets on time change
- Fix: NBM3/NBM365 should support 2 Ethernet ports but shows only 1.
- Fix: Aggregated transmission problems with some Apple laptops and other devices
- Fix: Clients can't reconnect to AP with WPA2-AES security reason (15)
- Fix: After upgrade from v5.3.5 to v5.5 secondary Ethernet port isn't configured (running default configuration)
- Fix: Stations disassociation because of returned broadcast packets on Ethernet interface
- Fix: Second LAN port MTU max is 2024B not 1614B (affected all M series products)
- Fix: No Internet connection for clients behind device in router mode
- Fix: Access Point ignores Session-Timeout limit received from RADIUS server
- Fix: Reduce false positives and misclassifications of invalid DFS radar events
- Fix: Can't launch Airview when initial window disabled
- Fix: Making changes in Network tab resets MTU to 1500 when Management VLAN is enabled
- Fix: Incorrect ebtables VLAN drop rules
- Fix: Do not allow to upload Configuration file from different Regulatory domain
- Fix: Port Forwarding public port range issue
- WEB UI: Show DFS status in MAIN page
- WEB UI: airSync: Show correct default slots depending on channel size
- WEB UI: Static route disappears in Router mode
- WEB UI: Option to disable Multicast Enhancement for AP
- WEB UI: Improved IP address validation
- WEB UI: Don't enable "DMZ Management Ports" when DMZ is enabled (Router/SOHO Router)
- WEB UI: Bridge table display problem. Table too big
- WEB UI: Do not show graph for interface when it is not in use
- WEB UI: Don't report TOUGHSwitch/airCam WLAN mode in device discovery results
- WEB UI: Add Turkish language support
- WEB UI: In Simple configuration mode LAN should be BRIDGE0 containing both Ethernet interfaces
- WEB UI: Show the same antenna information in MAIN page as in Wireless settings page drop down
- WEB UI: Site Survey Scan button is disabled under IE browser
- WEB UI: Allow MAC Cloning for BRIDGE interface in Router mode
- WEB UI: Bridge table is not displayed in Main page when there are multiple bridge
Security Improvements:
- WEB UI: Default settings change: Enable HTTPS (port 443) by default
- WEB UI: Removed admin.cgi functionality
- WEB UI: Add option to disable HTTP service
- WEB UI: Add reminder when using default admin user name/ password
Version 5.5 - Final Release (April 10, 2012)
--------------------------------------------
New product support:
- New: Bullet M2 Titanium
- New: Bullet M5 Titanium
- New: NanoStation M900
New functionality:
- New: Management VLAN support
- New: Advanced network settings configuration mode
- New: RADIUS MAC authentication
- New: Low TX power mode support for all M series models
- New: AirMax client support for 802.11 a/b/g products
- New: DHCP relay functionality in Router/SOHO Router mode
- New: UPnP server support in Router/SOHO Router modes
- New: Ability to Block WAN Access in SOHO Router mode
- New: Fallback IP for PPPoE client
- New: 3/8 MHz channel width support for M900
- New: 8/30 MHz channel width support for M2/M5
- New: 8/25 MHz channel width support for M3
- New: 25 MHz channel width support for M365
- New: Full range of channel width options in Compliance mode
- New: Max allowed MTU size for newer HW revision models is 2024 bytes
- New: Make Device name the Product Model by default
- New: Separate throughput graphs for LAN0/LAN1 interfaces
- New: Option to create support info file with ping watchdog before device reboot
- New: Enable/Disable CDP option in Device Discovery section
- New: Check for existing uploaded firmware image when opening System page
- New: Prepare for IPv6 support
- New: Traffic shaper for ingress traffic
- New: Notification for software updates
- New: Add PPPoE service name configuration
- New: Kernel patches for SIP conntrack/NAT support
- New: Show AirMax priority in Main page for Station mode
Fixes:
- Fix: Configuration change causes device with a long uptime to lock up
- Fix: Device stops passing traffic after some time and requires a reboot or "kick" to work again
- Fix: Dynamic DNS update after PPPoE session initialization
- Fix: Station list is empty when there are few stations associated
- Fix: Port ID is mandatory in CDP packet
- Fix: STA-WDS in bridge mode is passing back multicast/broadcast packets
- Fix: "Antenna Gain" and "Cable Loss" fields are locked for LocoM900 with external antenna
- Fix: Incorrect connection time reporting
- Fix: Timestamps reset because of stuck beacon. Causes other manufacturers' (i.e. Tranzeo) devices to re-associate.
- Fix: Can't launch airView with HTTPS enabled on IE8
- Fix: Traceroute fails to DNS host with multiple addresses
Improvements/Change requests:
- Improvement: Linux kernel update to 2.6.32 version
- Improvement: AirMax performance in large PtMP networks
- Improvement: AirSync performance in PtMP networks
- Improvement: ACL List: Dynamic list now allows instant changes (no restart or dropped connections required)
- Improvement: ACL List: MAC list limit increased from 64 to unlimited
- Improvement: ACL List: Ability to add comments to MACs
- Improvement: ACL List: Ability to enable/disable a MAC without removing it from the list
- Improvement: DFS functionality improvement according FCC/ETSI requirements
- Improvement: Report Horizontal / Vertical antenna instead of "Chain 0 / Chain 1"
- Improvement: New look for wireless mode configuration
- Improvement: Various WEB GUI tweaks, changes, improvements
- Improvement: Send NASID in Access-Request packet.
- Improvement: Add internal speed test tool to DMZ exemption ports
- Improvement: Hide Discovery Tool for read-only account
- Improvement: Extension for Port Forward configuration. Allow to specify Public IP
Regional Updates:
- New: Initial Login page with Country/Language selection
- New: Replace Obey Regulatory rules with Auto Adjust to EIRP Limit functionality
- New: Remove possibility to change country for some countries (USA, Spain)
- New: Remove indoor range for Brazil (5.1-5.3GHz frequencies)
- New: Show Band C for UK Frequencies
- New: Add Iraq country code
- New: Add Nigeria country code
- New: EIRP limits for US Regdomain on 2.4GHz and 5.8GHz band
- New: Add German translation
- Fix: Regulatory rules update for Australia
- Fix: Devices with selected country Ukraine doesn't work in 5GHz band
Additional Notes:
- Note: SNMP interface indexes have changed with v5.5 due to advanced network configuration options
- Note: AirControl v1 Configuration changes are not supported with v5.5 firmware
- Note: Possible Web UI issues with out of date browsers (i.e. Firefox 3.6). It's recommended to use current browser software
Version 5.3.5-Service Release (December 19, 2011)
-------------------------------------------------
- Fix: HTTP server security exploit
شبكة سكاي نت لخدمات الانترنت اللاسلكي
| |
|
اليومية